Delfleet One® Performance Range · MS = Maximum Sheen
Deep black.
Mirror gloss.
Built for the fleet.
The Maximum Sheen topcoat from the Delfleet One Performance range: a high-solids 2-pack polyurethane for commercial vehicles, VOC compliant when mixed 2:1:0.5, colour-mixed to order in Stoke-on-Trent and delivered across the UK by Beyond Surface Solutions.
4.9 from 210 Google reviews2 : 1 : 0.5Mix ratio by volume — VOC compliant
Topcoat · Hardener · Thinner
Topcoat · Hardener · Thinner
2 hrsPot life at 20°C
40–60 µmDry film thickness
2 coats
2 coats
8–10 m²Coverage per litre RFU
at 50 µm DFT
at 50 µm DFT
30 minBake at 60°C metal temp
HVLP / pressure pot
HVLP / pressure pot
The topcoat
Max Sheen Performance Topcoat
MS
MS stands for Maximum Sheen, not Medium Solids. Delfleet One MS is part of the Delfleet One® Performance range and is a high-solids product. Mixed at the specified 2 : 1 : 0.5 ratio, it is VOC compliant.
An easy-to-spray high-solids 2K polyurethane giving good opacity, high gloss and the general appearance demanded of commercial transport vehicles — for builders and repairers alike.
- Range
- Delfleet One® Performance
- MS means
- Maximum Sheen
- Chemistry
- High-solids 2-pack polyurethane
- VOC
- Compliant when mixed 2 : 1 : 0.5
- System base
- F8080 Max Sheen Performance Binder + F7xxx tinters
- Pack size
- 5 litre, mixed to colour
- Suitable over
- All PPG primers, surfacers and sealers
- Recoat
- With itself within 24 hours, no sanding
Trade tool · ready-for-use cost
What does Max Sheen cost ready to spray?
Enter your discount and see the cost per litre of Delfleet One MS mixed 2 : 1 : 0.5 with its MS hardener and thinner. Open the full calculator for separate hardener and thinner discounts, booth temperature, 1 litre tins and the complete price matrix.
%
5 L Max Sheen · net RFU per litre–
Trade RFU / L–Full 5 L tin batch–
5 L F8080 + 2.5 L MS hardener + 1.25 L MS thinner = 8.75 L ready to use. Prices ex VAT.
Finish
Reflections you can read.
Delfleet One MS is formulated for optimal colour selection and reproducibility when tinted with the latest generation of Delfleet® tinters — so a fleet repaint in Stoke matches the one in Aberdeen.
- Good opacity in two coats: one medium closed coat plus one full coat
- Dust free in 10–20 minutes at 20°C (HVLP / pressure pot)
- Through dry in 24 hours, or 30 minutes at 60°C metal temperature
- IR medium wave cure in 10–15 minutes
Where it's mixed
Colour-mixed in Stoke-on-Trent.
Every tin of Max Sheen topcoat is tinted to order in the Beyond Surface Solutions mixing room and labelled with its mixing point, so you always know where your colour came from.
Mixing & dispatch Beyond Surface Solutions Units 6 & 8 Britannia Park Industrial EstateNorth Road, Stoke-on-Trent ST6 2PZ
- 01Send your colourFleet reference, colour code or a sample panel.
- 02We tint & checkTinters machine-stirred, mixed by weight, colour checked.
- 03Labelled & dispatched5 L tins with the BSS mixing label, plus matched ancillaries.
Top Coat Ancillaries · 5 litre
Hardeners & thinners.
Matched to Max Sheen and chosen by booth temperature. Pick your conditions and we'll highlight the recommended pair.
Booth temperature
Medium / Medium — F8286 + F8375
Hardeners
Thinners
| Temperature | Below 18°C | 18–25°C | Above 25°C |
|---|---|---|---|
| Combination | Medium / Fast | Medium / Medium | Slow / Slow |
| Ancillaries | F8286 / F8376 | F8286 / F8375 | F8284 / F8374 |
Substrate & preparation
- Sound original finishes: degrease, clean and dry sand with P320–P400 (or P600 wet).
- Steel, aluminium, GRP and zinc-coated steel: pre-prime with the appropriate primer for adhesion and protection.
- Clean with D845 Degreaser and D837 Spirit Wipe (or D8401 low-VOC cleaner). Substrate must be dry and free of corrosion, grease and mould release agents.
Spray viscosity at 20°C
- Conventional / pressure pot
- 18–22 s DIN4
- Air-assisted airless
- 19–23 s DIN4
Coats & flash-off
- Coats
- 1 medium closed + 1 full
- Between coats
- 10–15 min
- Before bake
- 15–20 min
Gravity / suction feed
- Tip
- 1.3–1.5 mm
- Pressure
- 2.0–2.4 bar
Pressure pot
- Tip
- 0.8–1.0 mm
- Air cap
- 0.68 bar
- Paint
- 0.3–1.0 bar
- Flow
- 280–320 cc/min
Air-assisted airless
- Tip
- 9–11 thou (0.23–0.28 mm)
- Paint
- 90–110 bar
- Atomisation
- 2.5–3 bar
Good to know
- Allow at least one week of cure before applying decals.
- Let the finish harden fully before vehicle washes — this can take weeks if air-dried in the cold or applied too thick.
- Store tinters at 18–25°C in the mixing room; 5–35°C in storage.
- Always carry out a colour check before painting the vehicle.
Drying times
| Stage | HVLP / pressure pot | Air-assisted airless |
|---|---|---|
| Dust free at 20°C | 10–20 min | 20–30 min |
| Through dry at 20°C | 24 hours | 24 hours |
| Bake at 60°C (metal temp) | 30 min | 40–50 min |
| IR medium wave | 10–15 min | N/A |
Technical data sheet
The full specification.
Product list, substrates and preparation, mixing ratios, application set-ups, drying times, colour, storage and health & safety — in the manufacturer's official technical data sheet.
For professional use only. Always refer to the material Safety Data Sheet before use — ask us and we'll send the current SDS with your order.
One system. Every cab in the yard.
Talk to us about your fleet“Great Company – long standing customer of ours and would highly recommend them”Highlighted in BSS's Google review summary
Went looking for a paint match for a TR2 with a panel sample. Joe and Dillon were friendly and extremely professional in analysing the existing paint and then mixing the closed match which was perfect to my eye. These gents were exactly what a business needs in terms of expertise and customer service. Absolutely would go back and have no qualms recommending this company.
Called up these guys for some advice on a repair I was doing on my old MG and they suggested I popped in with the car to get the exact colour match and I must say it was brilliant they mix it while you wait! I ordered a couple of spray cans and it covered very well indeed. Thanks for your help with this.
These guys were brilliant in helping me. I had a royal blue electric (plastic) garage door and I wanted to change it to Chartwell green. I followed the advise on prep and applying a dust coat first followed by a final coat. The door looks fantastic saving me £650 in replacing the slats of the door. A big thumbs up to the team.
Perfect colour match highly recommend thanks guys
Reviews are reproduced word for word from the Google Business Profile for B.S. Supplies (BSS), Units 6 & 8 Britannia Park, Stoke-on-Trent. Rating and review count correct as of October 2026.
Enquiries
Pricing, colours & trade accounts.
Tell us what you're painting and the colour you need, or call us on +44 (0) 1782 209527. Our team will come back with pricing, availability and delivery.
Email
info@beyondsurfacesolutions.co.uk
Phone
+44 (0) 1782 209527
Web
beyondsurfacesolutions.co.uk
Trade counter
Units 6 & 8 Britannia Park Industrial Estate, North Road, Stoke-on-Trent ST6 2PZ